Monday, June 16, 2014

SQ Hans

This week I learned about using different scan tool software to check active codes on different engine. I was then able to use this same software to my advantage to troubleshoot t problems.
 
 using the modis to activate the horn and windshield wipers on the black dodge
 
 I was able to use the laptop to find the active code on the Cummins ISX and then I was also able to check the voltage to the VGT actuator.
 
I found the active code on the powerstroke using IDS. I was also able to use the IDS to monitor then fuel rail pressure and the voltage to the sensor that was causing the engine to throw a code. 

Monday, June 9, 2014

SQ Hans

 This week I finished the tear down and reassembly of my cylinder on the 3516 cat. This engine requires the you be very precise. Just how you hold the tools you are using can make the difference of out of spec or in spec, since some of the measurements require you to be accurate down to .0001". This kind of work requires a lot of attention to detail and cleanliness. I did a good amount of measurements on this engine, including measuring valves, lifter bores, rocker arms, liner, piston, connecting rod, wrist pin, and more, but looking through the service manual for this engine there is just about a measurement for anything and everything on this engine.
 
This week = 55, total = 564 

Monday, June 2, 2014

SQ Hans

This week I learned about how a thermistor functions. It functions in the same way as a potentiometers and is used in various applications where temperatures are monitored. A potentiometer functions using a resistor and a contact moves along the resistor as a path for voltage to flow and as the contact moves it  makes the voltage flow through more or less of the resistor. When less of the resistor is used the voltage is higher and when more of it is used then the resistance is lower, A thermistor functions when temperature rises and lowers. A reference voltage is sent to the ECM and the thermistor, the reference voltage is goes through a resistor to drop the voltage to 5 volts. When the temperature in the thermistor starts to rise less of the resistor in the thermistor is used and the resistance in the circuit decrease. Since the resistance in the thermistor decreases the voltage drop of the reference voltage increases. Using the formula voltage =amps x ohms shows that if the current flow is the same and the resistance is lowered then the voltage will be less.
 
 
Potentiometer
 
Water temp sensor using a thermistor 
 
This week = 62 

Temperature sensor circuit

Monday, May 26, 2014

SQ Hans

 This week my group and I finished our measurements and put the 3176 cat engine we were working on back together. Throughout this project we found several measurements that were out of spec. Some of the things that I had learned on this project were measuring the crank journals for the connecting rods, measuring connecting rods for out of round, and how to set the Jake brake adjustment.
 
 
 
   
 
  
  

Monday, May 19, 2014

SQ Hans

This week I learned about testing different sensors. One of them was a temp sensor, on this sensor I hooked the leads from my meter to each end of the sensor and tested the resistance through the sensor. Then I was able to use hot and cold air to make the sensor function and watch the resistance go up and down.

I also learned about three wire pressure sensors. These sensors have one ground wire a signal wire and a voltage reference wire. When pressure is applied to these sensors a plate inside the sensor moves to make contact and send out a signal voltage that is equal to or less than the voltage reference. The amount of voltage sent out is determined by the pressure put on the sensor and then that voltage reading is displayed on a gauge as a pressure reading.

Monday, May 12, 2014

SQ Hans

 This week I was doing a starting testing on an international truck that wouldn't crank over. I didn't have to get any parts for this truck because as I found out the spot where you test or dont test can mean the difference between new parts or just tightening a loose nut.
 
You can see the black spot on the post on the solenoid where there was a loose connection. This is where the point that you test makes a difference because on the solenoid post I got 12v and at the bar that goes between the post and the starter I got 0v
 
 
This was what is left from the last start before the truck wouldn't crank. A lock washer that was barely making contact, because of a nut that had loosened up,until the starting current melted it in half. The other half of the washer was welded to the nut. 
 
 
 
 I also completed my engine research worksheets
 


 
this week = 60
 

Monday, May 5, 2014

SQ Hans

 This week I was finally able to assemble my Eaton fuller RT-910 transmission. This transmission wasn't to hard to get parts for, but since it is out of a truck from 1966 it did take about a week and a half to get the input shaft and bearing spacer.
 
The input shaft goes in first and then a snap ring followed by the bearing spacer
 
 
to install this input shaft the top cover must be removed and the transmission locked into two gears to stop it from spinning. To install the input shaft bearing you want to hold the main drive gear against the front of the transmission case, I used a piece of wood wedged in to hold the gear from moving. Then the bearing can be installed on the input shaft.
 
 
Bearing installed
 
 
then a nut is threaded onto the input shaft, the nut also has left hand threads and gets torqued to 250 Ft lbs. I used red locktite on the threads and a gland nut wrench to tighten the nut. Then the nut gets penned on two spots onto the input shaft.
 
 
bearing cover installed with new gasket, clutch housing installed with new gasket, cross shafts installed
 
 
 
  
 
 
    
  
 
This week = 66